Reply To: "Staggeringly High Speeds" Print Parameters
That’s a fantastic analysis jkao, thank you for that!
View ArticleReply To: Resin suggestions for small high rez parts
Hey Tracy, these were all done in spot-ht with 0.75-1.0% pigment. Pewter is sometimes hard to photo, so apologies for that.Attachments:You must be logged in to view attached files.
View ArticleReply To: Lens modification thread – discussion of printing in 26um xy...
Ok, I’ve bit and purchased a Vivitek D912HD that I found used at a decent price.Vince, do you have designs/measurements for the mounting plate you made? That would save me quite some time getting mine...
View ArticleUsing grease oil to maintain the Titan
Hello there!I was curious where on the Linear Module I apply the grease oil to maintain it. If anyone could show with images that would be great thanks!
View ArticleClik here to view.
Reply To: Any good Modification to your Machine?
Did not take so long to design, I have basic layout attached, not all details are drawn but this is what I will detail out later (4 parts) to have machined, for now I’m leaving for a weeks vacation and...
View ArticleReply To: confused with field 4 in the print controls
Hello! How do you know how tall your supports are through Creation Workshop to input into the 4th zone. If you have a support layer do you have to deduct that from the overall support height?
View ArticleReply To: confused with field 4 in the print controls
If you want to have a region where there are only supports before the part begins (which is what I would recommend to start), you would need to deliberately raise the part (e.g. Move Z + some amount)...
View ArticleReply To: Lens modification thread – discussion of printing in 26um xy...
A brief look, this is a great projector but at the end of the day, do you feel the aberration will help that much? I realize a lot of your prints have taken up the entire build plate but I’m curious if...
View ArticleReply To: Lens modification thread – discussion of printing in 26um xy...
I sent before asking that Joel, does this mean you could effectively have a much larger build volume at a better resolution? Any idea how much better the xy res would be at the full 1920×1080?
View ArticleCreation Workshop: How do I change the dimensions to the floor grid.
Hello,I am getting use to the program but one issue I cant seem to figure out is how to adjust the floor grid. I see in other peoples videos that its longer than what I have by default.
View ArticleReply To: Creation Workshop: How do I change the dimensions to the floor grid.
You can adjust the size of the build volume / floor grid in Creation Workshop by going to the Configure Tab and changing the values for X, Y, and Z in the Build Size (mm) box. For 100 micron resolution...
View ArticleReply To: Debugging first print
I too can only affect the gamma via the projector. I’m turning the brightness down from 50 to 30 and increasing contrast from 50 to 60. Let you know if that helps. I’m having a lot of general...
View ArticleReply To: Debugging first print
physically the brightness param is only changing.I’ve set brightness to 20 contract to default of 50 gama to 2 from default of 5.The calibration grid is a bit less intense so lower light power but...
View ArticleReply To: Lens modification thread – discussion of printing in 26um xy...
I haven’t had any issues with loss of detail. I have been running into issues with part fit. In particular cases where, possibly due to both resin shrink and aberrant focus, holes become smaller and...
View ArticleReply To: Creation Workshop: How do I change the dimensions to the floor grid.
One more question. Where are those numbers coming from. Sorry for such beginner questions.
View ArticleReply To: Creation Workshop: How do I change the dimensions to the floor grid.
Our fundamental print dimensions come from the projector, which has a pixel resolution of 1920 x 1080 pixels. Our print resolution is always in proportion to that and will be based on how we distribute...
View Article