Clik here to view.
Reply To: Weak bond layers
and yes I can see a horizontal line at mix point, I read about “proper mixing” but didn’t talk about what is proper and what is not….what I feel I want is a thicker resin to support pigment longer so I...
View ArticleReply To: File load doesnt work any more
You will see that error if you cannot write into Kudo3D_Titan folder. Usually it happens when you have multiple user accounts on the same computer. Please give the permission to the user or install the...
View ArticleReply To: better prints with spot HT
HiAre you printing with the projector as it is, or with the lens modification ?(putting 1,6mm spacers)Thanks!
View ArticleReply To: spot of light
The window for the sliced layers should take over the projector once you start printing. Occasionally, the display of the computer is not stable and may trap this window in your primary display and...
View ArticleReply To: Weak bond layers
Please try not to disturb the printing as much as you can. We never stop the print to stir. We usually stir it with a soft brush and only do it gradually over several layers when there is no exposure....
View ArticleReply To: Anyone in the SF Bay Area?
Hi All,Sorry we missed this event. Thanks for coordinating!We’d love to join a future meetup.Regards, Kudo3D
View ArticleReply To: better prints with spot HT
Hi @Patricio,no modifications to the projector, I’m happy with the resolution I get at 37xy 30z.
View ArticleReply To: better prints with spot HT
Thank you for your prompt response. Could you please tell me the vertical distance between the floor of the printer box vs the lowest part of the projector?
View ArticleReply To: better prints with spot HT
@patricio I’m not in home now,I’ll measure the distance when I get backhome, and post it tomorrow.
View ArticleReply To: quartz vat
Thanks for the tip. I’m thinking of making an experimental vat from one of these:http://www.geek.com/mobile/fingerprint-proof-flexible-plastic-gorilla-glass-1530961/and coat it with superhydrophobic...
View ArticleReply To: better prints with spot HT
@patricio i measure the distance between the bottom of the projector and the lower part of the frame?, i take some pictures, i hope they help, i measure the plate that hold the projector...
View ArticleReply To: Amazing high resolution 29mm tall miniature, cast in resin.
where are the support being made for this? I don’t see control to do supports in CW like this
View ArticleReply To: Amazing high resolution 29mm tall miniature, cast in resin.
@tdixon1000: I believe @Joel mentioned this earlier in the thread when he said:I didnt use Meshmixer supports, dont really get on with them. I have been using the softwear for the B9Creator, its got...
View ArticleReply To: very cheap vat fix
Alani received the FEP 12″ wide tape, cut my rectangle out of it, it went on easily with no bubbles (simple dry application )..i can say when its down its down.i am on my 4th full scale print @ 80...
View ArticleReply To: Chill Penguin Megaman X
Really nice print, thanks for sharing!Would be kind to know what exposure time you used on the 75xy 50z resolution?
View ArticleReply To: very cheap vat fix
@Martin,care to share the link where you bought that FEP tape ? and how did you do it ? The current FEP film just peels like that ? no cleaning ? Then how did you apply the new tape film to avoid dust...
View ArticleReply To: Amazing high resolution 29mm tall miniature, cast in resin.
@ Joel. Really nice miniature print. Its good to know someone else is using the B9 software. I am also printing 28mm figures with my Titan and stalactite and I am starting to match the quality of older...
View ArticleReply To: very cheap vat fix
Hughesi purchased the tape from CS Hyde in USA link belowhttp://catalog.cshyde.com/viewitems/all-categories-tapes-with-adhesive-ptfe-tapes/fep-optically-clear-ptfe-tape?i purchased the 12″ x 12″ to try...
View ArticleClik here to view.
Minimum Recommended PC Hardware Specs?
Hi all, hope I’ve posted this in the right section.So I’m about to get my printer, and I’m shopping for a laptop to run it from. How much hardware do you guys recommend in terms of RAM and processor to...
View Article
