Reply To: [DIY] Flex VAT for Titan1
Polycarbonate is a much stronger UV blocker than acrylic, and will have a larger impact on slowing down layer exposures.Extruded acrylic is very vulnerable to crazing when exposed to IPA. Cast acrylic...
View ArticleReply To: Amazing high resolution 29mm tall miniature, cast in resin.
Congratulations Joe,the impression is very good. You have printed at 25 microns; I guess you have modified the projector lens … I took time trying to make me Titan 1; but I find accurate … you could...
View ArticleReply To: [DIY] Flex VAT for Titan1
Hi James,thank you for the reply. Yeah I will be using cast acrylic. If polycarbonate works with resin then it wont matter regarding the uv issue I guess. Because the acrylic or polycarbonate parts...
View ArticleReply To: Toxic outgassing in the house
@ryanlesser are you still having the smell problem? I discovered two types of smell… The horrid odor I described above which has not recurred, and the other is a mild smell that is stronger in cycled...
View ArticleReply To: [DIY] Flex VAT for Titan1
Hello everyone, since I am not sure where to get or how to make those parts for the Flexvat, does anyone know where can I buy one pre-made? Does this one from MakeX work with Titan 1?...
View ArticleClik here to view.
Reply To: Alternative Castable Resin
Sorry for the late reply 3dps. Have been busy lately. Yay, congratulation to us. I saw those horizontal lines too, but I didn’t think it is a big issue, so never really pay attention to that, but I...
View ArticleReply To: [DIY] Flex VAT for Titan1
I have used the Muve3D flex vat (http://www.kudo3d.com/forums/topic/muve3d-flexvat/) and @kevinrau has used the FSL3D super vat...
View ArticleReply To: [DIY] Flex VAT for Titan1
From the dimensions, the MakeX flexvat will probably work in the same way as the other vats that people have tried, so long as you use the small build plate.The large build plate won’t fit in any of...
View ArticleReply To: Alternative Castable Resin
Hey Sovann,I just wanted to write to you this morning and you have beaten me to it :D.Well my rez isn’t 37u because I would rather sacrifice the sharpness in the middle for bigger rez and more rings....
View ArticleReply To: Video: Cleaning Up After a Print
Got a few direct questions on this, so for the record:The spatula is the red one from this set:https://www.amazon.com/gp/product/B00BSDP7FG/And the tea strainer is this...
View ArticleMinimum printing speed?
Hi, I’d like to print at less than 1mm/min for a proprietary resin, but Kudo3D software and gcode instructions for e.g. 0.5mm/min are not obeyed. I’ve looked in the firmware and apparently it takes 836...
View ArticleInterior fill for 3d prints
I’ve made a print out of 3DM-ABS and it’s a 9″ tall figure that I’ve done as a comission and is supposed to be Oscar like. I’m about to fasten the print parts together but am considering filling the...
View ArticleReply To: Interior fill for 3d prints
According to this tech supposed conversation with a Franklin International (the makers of Titebond) engineer, wood glues contain about 50% solids and thus have significant shrink.The net shrink of a...
View ArticleReply To: Interior fill for 3d prints
I have a .25″ + hole for the neck and arms to access the interior cavity with. I also have 6 mm diameter holes at the bottom of the feet that were required for this print. So I need to now seal the...
View ArticleReply To: Interior fill for 3d prints
I think your best is to look at the polyurethane casting resins we were considering back in this thread:Casting Epoxy for Phone Casesand if you want weight, to mix up a slurry with some kind of metal...
View ArticleReply To: Interior fill for 3d prints
Thanks Jkao, going to test this with adding BB’s as suggested by another person mixed in with some Polyurethane 380 from Smooth-on.I’ll report back but should work well.Jason
View ArticleReply To: Minimum printing speed?
Can you post the g-code you are trying to execute?Are you lifting with something like G1 Z8 F0.5?
View ArticleReply To: Minimum printing speed?
Yeah that’s right. I’m at e.g. Z10 and type G1 Z11 F1, time it, and it takes 1 minute as expected. If I type G1 Z11 F0.5, it takes 1 minute and 40 seconds – as does any number below F0.6 – with the...
View ArticleSome problem with cured resin at VAT resin tank
Hi everyone I hope you all doing ok!Few days ago i print some object using my Titan1, i’m using Makerjuice G+ Black resin, V1 VAT resin tank, and setting the machine with xy 50 micron and z 100 micron,...
View ArticleProblem with size prints Z
Hi friendsI just saw something very interesting with both …Because when I altered the value of z layer thicknes me alter the value of Z scale of the object?when do I put the slicer value thicknes layer...
View Article