Reply To: Vat 2 version Issues
Dear james kao,I always used default settings, I only changed project Z direction to micron 37(x=71.1 y = 40) In default 37 micron, printing area place in right side of vat. I’m using spot-ht tough...
View ArticleClik here to view.
Reply To: Vat 2 version Issues
Dear james kao,I always used default settings, I only changed project Z direction to micron 37(x=71.1 y = 40) In default 37 micron, printing area place in right side of vat. I’m using spot-ht tough...
View ArticleClik here to view.
Reply To: Vat 2 version Issues
I took These pictures from my Bubbled Vat ver 2(place with soap liquid) I tried remove those bubbles from my insurance card, when i pressing hardly silicon damaged & bubbles are shifting to inside...
View ArticleClik here to view.
Reply To: Z-axis way off for me…
First attempt failed! The piece came off the plate but something is possible to see. I’ll do another print this evening. The first layer of cube is instead a parallelepiped as you can see in the pics....
View ArticleReply To: Z-axis way off for me…
Here are the pics of the first print … but I’ve realized I made some mistake when sliced the object. The piece has X/Y dimension of 12.5mmx12.5mm instead of 25mmx25mm exactly the half … I don’t...
View ArticleReply To: Vat 2 version Issues
Yeah, I’ve never actually tried it myself, so I’m sorry that the soap method was a bust.When you put the film down, how did you do it? Did you start with one edge and then try to press it down little...
View ArticleReply To: Vat 2 version Issues
The fact is teflon does not stick to anything, neither silicone. It only stays there due to vacuum forces, once you lift a corner and let the air get in its over. I’m looking forward a more robust...
View ArticleSoftware changes or updates in Kudo 1.43
I’m looking at installing the new software but not sure where to find the changes/updates section so I know what has been updated?Thanks,Jason
View ArticleThe world of magic 3D printers
Do you want a 3D printer that belongs to your own? A magic machine that instantly turns into reality.
View ArticleReply To: [DIY] Flex VAT for Titan1
I made silicon gasket. 1st picture shows silicon is poured in the mold. 2nd picture shows silicon gasket completed.Attachments:You must be logged in to view attached files.
View ArticleReply To: [DIY] Flex VAT for Titan1
Interested to see how it works. I’m curious too why the new firmware update has expanded the zero decimal placeholder. Wonder if this is related to the sometimes appearing 50mm print line as tdixon1000...
View ArticleReply To: Software changes or updates in Kudo 1.43
Guess it’s really just the decimal precision..
View ArticleReply To: [DIY] Flex VAT for Titan1
It’s just a display change so that when you move by 0.05 increments you can see it in the current position display. Based on tdixon1000’s examination of the line under his microscope and my own...
View ArticleReply To: [DIY] Flex VAT for Titan1
I’m curious how much tension your putting on the FEP in both of these designs. Is it a lot to the point where when your tightening down the top plate to the bottom plate over either type of tensioner...
View ArticleReply To: Creation Workshop released 1.0.0.75
I’ve seen a bit more success in the slicing – I used to get some odd artifacts in the png’s on occasion. Jkao also mentioned that a ton of memory leaks were cleaned up, so overall it probably a good...
View ArticleReply To: [DIY] Flex VAT for Titan1
tdixon1000,What a amazing job you did!!!Yes, I realized the FEP film became bulge when it print large surface. Locating glass under the film is great idea.Especially it happens when first layers are...
View ArticleReply To: [DIY] Flex VAT for Titan1
The FEP can take a surprising amount of tension, it’s very tuff material, at the time I’m finding no stretch but maybe I have not had it in service enough….I don’t have anything here to measure this...
View ArticleReply To: [DIY] Flex VAT for Titan1
ILHYOUNG, you can see my progress here on this endeavor http://www.kudo3d.com/forums/topic/any-good-modification-to-your-machine/
View ArticleReply To: 3DM-XSeries
I bought X-series and Flex from 3DM…waiting for shipment now…will post once I play a bit with it…The X looks very very functional from the vid!
View Article