Reply To: Calibration Grid right against the edge of the build plate.
You can move the linear stage a little bit to bring the image closer. This projector is qualified for large area projection. According to the projector manufacturer, there are slight difference between...
View ArticleReply To: Fan stopped working
We did not experience this but we did add a fan on/off button in case the communication between the computer and mega got lost.
View ArticleReply To: Looking for a UV Bulb Compatible with my SLA Projector
You will get no light out since the UV cut filter will remove almost all of the UV. If you remove the UV filter, the UV will kill the DMD chip inside the projector.
View ArticleReply To: Please help: Printer stopped working
If the problem persists, please contact us directly.
View ArticleReply To: volume printed with 500ml of resin
The resin will shrink and also lose some solvent. Bulk shrinkage is about 3% so the cured solid volume is a little smaller than uncured volume.
View ArticleReply To: Spot-e elastic resin
We tried the Makerjuice elastic last year but the material was too weak. Not sure if MJ improved it or not. We tested the new Spot-E elasticby by printing a ball. We squeezed it and it comes back to...
View ArticleReply To: vertical surface quality.
For a tube shape, you would need to tilt it to avoid printing at the same spot. Printing at the same spot will generate huge adhesion for some layers. This force will create horizontal lines. Also, the...
View ArticleClik here to view.
Reply To: Spot-e elastic resin
I’m sold, will place an order to buy a bottleDoes this have pigment in? Does it settle and cause headaches? This reply was modified 20 hours, 16 minutes ago by tdixon1000.
View ArticleReply To: Creation Workshop: How do I change the dimensions to the floor grid.
So this means more higher resolution settings more smaller area on built plate you can use to print the model?
View ArticleReply To: ABS Resin Durability
I wouldn’t call it over-cured. A part it fully cured when it’s fully polymerized. Depending on the binders, when all of the polymers have linked up and formed a solid, the part may have varying flex.If...
View ArticleClik here to view.
Reply To: ABS Resin Durability
“Interestingly, Formlabs announced its “Tough” resin today: http://formlabs.com/products/materials/tough/ Their page touts a 52.2MPa (7570 PSI) tensile strength and 31% elongation, which compares...
View ArticleClik here to view.
Reply To: Z-axis way off for me…
I’m experiencing something very similar. I’m printing Marvin by 3DHubs as a reference model but it comes out with a strange elongation (is not linear, it seams that “accelerate” towards Z Up). I’ve...
View ArticleReply To: Z-axis way off for me…
Hmm… it’s hard to figure out exactly where the problem is occurring on the rotated part, especially if your feeling is that the elongation increases as the Z height increases.Could you try printing a...
View Article[DIY] Flex VAT for Titan1
I wrote some post I had trouble with VAT ver.2.So, I researched how to fix and I found below post. Also, I realized there are some posts in here about Flex...
View ArticleClik here to view.
Reply To: [DIY] Flex VAT for Titan1
After the design is done, I cut 0.5″ thick acrylic panel with my CNC.I am still working on making tensioning riser and resin wall.From right to left in attached picture. Top clamp panel, bottom clamp...
View ArticleReply To: Vat 2 version Issues
I tried several times to keep Teflon film on Silicon from several method, Sad to say it is impossible to do without having air bubbles.1 – 1st time i tried without any soap & try to remove air...
View ArticleReply To: [DIY] Flex VAT for Titan1
Interesting, do the parts have a 2.5D profile that could be cut on a laser cutter rather than CNC?
View ArticleReply To: Vat 2 version Issues
If you have parts that, when printed, resulted in the film lifting, would you be able to upload the STL, Kudo3D print settings (csv export), and a description of where on the build area you placed the...
View ArticleReply To: [DIY] Flex VAT for Titan1
James,Yes, some holes have 2.5D. I am planning to use Ribet nuts as listed in Amazon....
View ArticleReply To: 3DM-XSeries
Please, contact us via our website http://www.3d-materials.org Thanks for your understanding
View Article
