Reply To: Thin white line at bottom of projection between layer prints.
It’s strange, you shouldn’t need to change taskbar configs or color because of 2 reasons: It shouldn’t be any taskbar in second screen by default, only at main screen. The kudo projects as full screen,...
View ArticleReply To: Meshmixer for generating supports
Meshmixer is getting great! I also suggest to give a try on auto-orientation(analysis) feature. I did get some great results with it.
View ArticleReply To: Calibration Grid Usage Video
I would just add a final step to the process. – After fine tuning the focus I drop a clean white sheet over the VAT and gently mark the four corners of the projected grid with a pencil. – I then get...
View ArticleReply To: Ugly horizontal lines…
Yes, it’s too large, anyhow, I moves on with other projects as this line problem whipped me…I came back after a few days and tried again, this time I took my exposure and increased it from 9.5sec to...
View ArticleReply To: Ugly horizontal lines…
I wonder if this is a float vs. integer error thats built into the projector it’s self? I’ve only entered int’s in KudoSoftware and CW. I’ve had very little time this last month to print but it would...
View ArticleClik here to view.
Reply To: Ugly horizontal lines…
Ignore the last post, it just can’t be that. Only reason I’ve thrown this out is I don’t get this ellusive 50mm line your refering to but as my old laptop stops printing and freezes only when I run...
View ArticleZ-axis way off for me…
Hello everyone, I am seeing a large problem with the Z axis. It appears to be off by quite a bit. I just printed a part that is supposed to be .260″ vertically. It turned out only .158?? This is WAY...
View ArticleReply To: Z-axis way off for me…
Can you post a screenshot of the Kudo3D host settings page and the Creation Workshop slicing profile? You should check to see that the Z layer height is exactly the same between the two.Also, what XY...
View ArticleReply To: Z-axis way off for me…
Thanks for the responses. I just double checked the slice settings vs the kudo software settings for layer height and they are both set at 0.075mm. I will also redo my zero to see if that helps.James,...
View ArticleReply To: Need to Calibrate Z-Zero when Using a New PSP Resin Container
@systemnova – Please see below for two videos we have currently:We will provide another video soon with more description. In general we lower by 0.1 mm until the 4 corners of the build platform doesn’t...
View ArticleReply To: Z-axis way off for me…
Z-axis compression is just a short way of describing the symptom of the modeling being squished in the Z dimension somehow.There can be several different causes.What I recall seeing described thus far...
View ArticleABS Resin Durability
Hello Everyone, I recently purchased a Kudo printer with some of the orange ABS resin. I understood this resin to be more durable like an ABS material. I was just playing with my very first print, and...
View ArticleReply To: ABS Resin Durability
Photopolymer resins, in general, will not have as much tensile strength or handle as much deformation as thermoplastics like ABS, PLA, or polypropylene. Resins can be harder (Shore D), more temperature...
View ArticleReply To: ABS Resin Durability
Thanks for the response. I know it probably depends on part geometry, but how long should I be curing these parts in the UV chamber?I know photo resin the can handle the stress I am seeing here because...
View ArticleReply To: ABS Resin Durability
3DM-ABS doesn’t need much at all. 15 minutes should be fine, 30 if you want to be totally sure.There are some types of resins that do also get harder (which isn’t necessarily stronger, it may be more...
View ArticleReply To: ABS Resin Durability
OK, So I did a little test. Printed a nice little flat .100″ square of the ABS resin. When I removed it from the build platform it was a little gummy as to be expected. I did play with it, and it...
View Articlevertical surface quality.
OK so I have some larger parts that must be printed vertically. But with the layer lines, the surface quality leaves a little to be desired. So my question is, are there any settings to tweak to remove...
View ArticleReply To: vertical surface quality.
Thanks for the response. What thickness do you usually print at? I have running mine at 0.075mm.
View ArticleReply To: Drill bit types for 3D resins
We tried standard carbide on 3DM ABS-Like and it is fine. Spot-HT is not brittle and should be fine with standard drill bits.
View Article