Reply To: 60mm figure with lots of thin protruding parts
Yes, sorry I meant .1mm height for the base!I acutally have it set to print the base at 2 layers at .1mm slices, so it will be .2mm max in height. Thanks again, sending it off to print soon just got...
View ArticleClik here to view.
Reply To: A more detailed walk through of software setup needed
Hi jkao: How do you prepare an STL in the sliced format needed by the printer software? I´m trying to follow the step #6 in the printing guide dealing with slicing a model using Creative Workshop but...
View ArticleMuhammad Ali print success!
First attempt today failed, but tonight had my first success. Resolution isn’t too great, but happy the print went through. There are some flaws, biggest is that the majority of his left glove didn’t...
View ArticleReply To: Vat plate appears to be installed backwards
After looking at it again tonight based on Kudo3Dsupport, when I unplug the USB connection from the controller board, and still have the Green plug power supply plugged in; there is no LED light on the...
View ArticleReply To: Muhammad Ali print success!
Looks like your heading in the right direction for sure! Ali is a neat subject to print. Did you make the model? Might post a shot of the model in Cura or 3D app too so we can see what the print is...
View ArticleReply To: Vat plate appears to be installed backwards
I made a quick video showing the connections to the controller board. As this felt a bit glossed over in the manual, thought it might help someone else. Also learned that the power supply when plugged...
View ArticleReply To: Muhammad Ali print success!
Hello co3Dprints,Thank you for the comments, it is a pleasure to meet you! Yes I made the model, it is an older commission that was quickly sculpted in ZBrush for jewelry. I wanted to use him for...
View ArticleClik here to view.
Reply To: 60mm figure with lots of thin protruding parts
Hi jkao, I finally had a successful print and posted the info on the forum here http://www.kudo3d.com/forums/topic/muhammad-ali-print-success/#post-9201Also attached are the settings I used for SPOT-HT...
View ArticleReply To: 60mm figure with lots of thin protruding parts
Higher exposure times can cause increased light bleed in less pigmented resin, but probably won’t have any such side effects for resin as pigmented as yours appears.If you ever try printing on bare...
View ArticleReply To: 60mm figure with lots of thin protruding parts
Ok great, thank jkao. I was concerned that although increasing exposure time might strengthen the layer, it might decrease overall resolution of the layers.
View ArticleReply To: 60mm figure with lots of thin protruding parts
I wouldn’t overestimate the “strengthening” effect of increasing exposure time. Resin is either solid or not. (There are a few stages of “not” ranging from “slimey” to “watery”, but none of them are...
View ArticleReply To: 60mm figure with lots of thin protruding parts
Thank for all the info! Doing my own prints is new to me, so I am trying to soak up as much as I can.May be trying another print sometime the next few days. Goal is to try larger size with smaller...
View ArticleReply To: Ruby Top
Don’t follow Kudo’s ruby top cover instructions-they are incorrect. The ruby cover goes together like this… The bottom of the rear piece (the only piece perpendicular to the ground) fits around the...
View ArticleReply To: Fan motor not working.
Thank you Jensa for “M106 S127″ to start the fan. Worked for me.When the Kudo software shows the printer is connected, enter “M106 S127″ at the bottom-in the text box.And I forgive you for the errant...
View ArticleAutodesk Emeber vat
Just curious if anybody knows about how the separation is working with the future Ember 3D printer.There is one timelapse video of it and it appears to use the same PSP technology, but hard to tell. If...
View ArticleReply To: Autodesk Emeber vat
It uses a sloped slider, similar to the B9Creator, but with a rotational rather than linear direction.
View ArticleReply To: Ruby Top
I just assembled my Diamond, and in all fairness it wasn’t that bad. I made a mistake however and have a small gap on both sides at the rear of the top triangle piece. Did it in haste but with my...
View ArticleBuild Plate Height when Starting Print
I apologize for the double post, I believe this is the correct forum for my question.Regarding the build plate height when starting a print. After placing resin in the vat to begin a print, is it best...
View Article