Clik here to view.
Reply To: HDMI output and the Projector control fixed
@jkaoHiI can control the Z calibration from my laptop using the Kudo software. But I can´t turn the projector ond / off from that software, I must do it manually from the projector, and everytime I...
View ArticleReply To: HDMI output and the Projector control fixed
If turning projector on and off causes your laptop to reboot, then you have more significant Windows problems.Turning on the projector will trigger the sequence in Windows by which is adds a display...
View ArticlePrinting at .05 layer thickness
How do you calibrate the machine for a .05 layer thickness print?I understand that setting the projector at 192mm x 108mm you will get a 100 micrometer (0.1mm) resolution. Is this the same as setting...
View ArticleReply To: Printing at .05 layer thickness
You are not obliged to move your projector to print at lower Z res than 100. Slice at 0.05 and set the Kudo software at 0.05 mm layer and leave the other parameters the same.I always print like this...
View ArticleClik here to view.
Reply To: Printing at .05 layer thickness
Excellent, thank you for all the info Hugues. A big help as always! This reply was modified 13 hours, 41 minutes ago by michael milano.
View ArticleReply To: HDMI output and the Projector control fixed
@jkaoHiKudo tech support asked me to try with another computer to see if was able to turn the projector on/off. Here is a copy of my answer:HiGood and bad newsMy other computer (HP Elitebook mobile...
View ArticleReply To: HDMI output and the Projector control fixed
Automatically turning on and off the projector is mainly a convenience, especially the turning off part if you are printing unattended. However, if that doesn’t work, it won’t prevent you from...
View ArticleClik here to view.
Finally had some time for printing again…
I finally had time to do some printing again this weekend as I organize bi-monthly 3D Printer Weekends at my local hackerspace. People from all around the southern parts of Norway meet up for two full...
View ArticleKudo Software, Offset X & Offset Y
My assumption, If I send a file to the printer of a round rod diameter of 10mm and the print ended up 9mm, can I add to both “offset X and offset Y” 1mm positive value to make the print come out to...
View ArticleReply To: Kudo Software, Offset X & Offset Y
Ok, tested a part with offset X & Y value at .5mm, it did not change the size of the part, it may of changed the linier location in a horizontal plan by this amount on build plateform but can’t...
View ArticleReply To: Help required castable resin prints @ 37um
Thanks Jkao for the info. On other prints with G+ resin, my problem has being that for example, instead of the part printing round, it turns out oval. The xy parameters are good but the z factor is not...
View ArticleReply To: Kudo Software, Offset X & Offset Y
After the print, again I don’t see any change with size, any input with either of these adjustments?
View ArticleReply To: Kudo Software, Offset X & Offset Y
i do these scaling in Creation Workshop before slicinghttp://www.envisionlabs.net/
View ArticleReply To: Kudo Software, Offset X & Offset Y
I hear ya, was hoping I could do some quick changes in Kudo software, any idea?
View ArticleReply To: Kudo Software, Offset X & Offset Y
Offset X and Y do not change the size of the image. It will move the image by a the number of pixels specified (you can enter both positive and negative numbers).The only times I have used this have...
View ArticleReply To: Help required castable resin prints @ 37um
Tilted parts coming out with the wrong Z aspect ratio tend to be caused by a mismatch between the slice thickness set in CW and the matching parameter set in the Kudo3D software.You should always...
View ArticleClik here to view.
Reply To: Finally had some time for printing again…
Nice… so bi-monthly would mean your next meeting will be in May? Do you know the date yet?I also noticed something familiar looking but in blue in the picture of your hackerspace. I didn’t post this...
View ArticleReply To: carbon 3d and oxyegen permable glass
Saw that article today as well, and amazed by how fast it can print.
View ArticleReply To: Ugly horizontal lines…
Thanks for your input guys,yeah i guess i need to give it another try printing at an angle.But i’m not sure which angle because i don’t fully understand what really creates these lines. I’ve uploaded...
View ArticleClik here to view.
Reply To: carbon 3d and oxyegen permable glass
heres a quick sketch i worked up of a possible hidea how to make this work its really rough and prob completley flawed, but just brainstormin. it uses a plastic tray split in half with film stretched...
View Article