Reply To: UV Sterilizer Cabinet for Salon – Spa
Same here, speeds it up big time.But: after cleaning my part with a bit of IPA, then i rinsed in distilled water before curing, this leaves a whitish coating on the part. Do you have the same problem ?
View ArticleReply To: Chill Penguin Megaman X
Hi Tracy, Would you mind sharing your cws for that print. I have something similar I want to start printing and experimenting with Kudo software for. Have you printed anything similar to Chilleman...
View ArticleClik here to view.
Reply To: UV Sterilizer Cabinet for Salon – Spa
mmm… update on my poste above,today i cleaned the part with IPA after printing, removed the excess with my air compressor, then put the part in distilled water for curing. Now after 2 hours the part...
View ArticleClik here to view.
Reply To: UV Sterilizer Cabinet for Salon – Spa
I find that the whitish coating on the part is resin that has reacted with IPA that is then subsequently cured. I’ve read postings elsewhere where people have hypothesized that water had something to...
View ArticleClik here to view.
Reply To: UV Sterilizer Cabinet for Salon – Spa
As I can respond again in the forums I’ll finally reply to JKAO, that yes it’s 45 min to an hour to get it non sticky. I did a Donkey from shrek print last night and when I got to my office it failed...
View ArticleReply To: Finally had some time for printing again…
Jensa, Since many of your posts seem to be what I have needed for setup (Kudo should be paying you for what they cannot be bothered to do), could you please post your results (successful and...
View ArticleReply To: Ugly horizontal lines…
3rd try now for my part, still no success:increased exposure time to 6 and 8 sec, still horizontal lines, printed only the external shell without any internal features, still horizontal lines.It’s been...
View ArticleReply To: Finally had some time for printing again…
@Koogie, there are lots of sample prints with settings in the Showcase topic if you look through it, although if you really want to have a successful first print, I suggest you use one of the Kudo3D...
View ArticleReply To: Ugly horizontal lines…
At 100xy, I found that FTD didn’t really have a noticeable increase in hardness until I went up to 8 seconds, and got even harder still at 14 seconds per layer.
View ArticleClik here to view.
Reply To: Ugly horizontal lines…
I’m curious if these are just test prototypes, do you plan to use castible resin when you get the recipe you need? I’d imagine your close but if you switch to castible now you’d save having to dial in...
View ArticleConservative Settings
I have my Titan1 setup remotely. Not allowed to have in the house cause we have young kids and I agreed to this as I wasn’t sure what the toxicity would be of the resins. I now realize It could be...
View ArticleClik here to view.
Reply To: Conservative Settings
Yeah, such a thing would be a panacea, but I suspect it would be difficult.A key input to generating such a table is the max surface area of the print in a given zone, and also need to take into...
View ArticleReply To: Ugly horizontal lines…
@co3Dprints: the part i’m showing initially in my left hand in the video is supposed to be the final part i’m using on my bike, it’s a bracket to hold the passenger footpeg. It’s filled with epoxy...
View ArticleReply To: Ugly horizontal lines…
Yeah, it seems that all of these resins are nowhere near as strong as common FDM thermoplastics like real ABS or PLA, although they are significantly more heat resistant. Parts I designed with 1mm...
View ArticleReply To: Conservative Settings
I am a Maya user so after I’m done generating my slices, I load them in Fcheck. It’s a image sequence utility that ships with Maya. There are others out there if anyone’s interested. I like to use it...
View ArticleReply To: Ugly horizontal lines…
Hugues, I too found a problem like this, look at “Layer thick change within print”, anyhow nothing made rime or reason of why, and I had NO internal structure change at all to influence this problem, I...
View ArticleReply To: Ugly horizontal lines…
@hugues: How many mm up and how thick is that wall at the point of imperfection? I’m printing a shelled part flat against the build plate and I want to see if I can reproduce the issue.
View ArticleReply To: Ugly horizontal lines…
Thanks guys for the ideas and time you spend on that, much appreciated.i printed at 0.050 mm, using anti-aliasing set at 3.5 layers 1 to 7 = raft 8 to 67 are the supports so part starts at layer 68 or...
View ArticleLight Dots on Projected Image
Hello Kudo3D community,I just recently discovered that my data projector which is original provided by Kudo3D (Acer 6510BD) has a weird light dots when projecting. Does anyone have an idea what could...
View Article