Reply To: Z axis compression… constant failures…
Thanks for all the replies!Just woke up to start again.I recalibrated the printer to 37xy last night. I will start with the Kudo calibration model today. I’ll rework my slicing to match at 37, check my...
View ArticleOpen Letter To Kudo team–Response to jkao 10401 reply
Jkao,To reiterate, thank you for your videos, for me they were very helpful in getting me started..As far the videos I would add (a) Step-By-Step of using Arduino to get the increased z-axis (b) How to...
View ArticleReply To: Thin Film Of Exposed Resin On Vat Bottom Making Long Print Times Fail
I am at 100microns x/y/z and my focus is spot on, with my calibration block measuring almost perfect (meaning off by less than 0.05mm).Looking at the bottom of the vat while printing the white is nice...
View ArticleReply To: Thin Film Of Exposed Resin On Vat Bottom Making Long Print Times Fail
Also, it does appear to match the entire 100um 1920×1080 area. I always make sure that when I have the software on and the projector before a print, that the lens of the projector is covered. If you...
View ArticleReply To: Software suggestion
GCode is like logo, so no if statements or loops. It’s not really a programming language by computer science standards.It is, however, designed to be executed in real time with some particular...
View ArticleReply To: Open Letter To Kudo team–Response to jkao 10401 reply
jkao, I will politely and respectfully disagree with you on the documentation aspect.Having been in the product development business for almost 20 years I am very familiar with the process of...
View ArticleReply To: Thin Film Of Exposed Resin On Vat Bottom Making Long Print Times Fail
I think the picture is a little deceptive and the film tore when I removed it but it covers the majority of the vat bottom (I assume since the projector is less intense in the corners it cures there...
View ArticleReply To: Thin Film Of Exposed Resin On Vat Bottom Making Long Print Times Fail
Panagiotis,You are not the only one who has this problem. I have this issue, too.I have 3DM-ABS and 3DM-DENT resin. When I printed it took around 4-5 hours and I saw the thin half-cured layer at the...
View ArticleReply To: Thin Film Of Exposed Resin On Vat Bottom Making Long Print Times Fail
ihkim,Thank you for responding, its helpful to know I am not the only one having this issue.I think the more reactive (sensitive to light) resins will show more of this problem, if using the same...
View ArticleReply To: Fan stopped working
Fan still stops, the sequence is once print is finished/ load new file/turn on DLP the fan either does not turn on or turns off soon after, not sure which one…anyhow this problem with fan seem to be...
View ArticleReply To: Z axis compression… constant failures…
Sorry for the late reply. I didn’t get a notification and forgot to check.Today, I’m going to go back and recheck my build plate calibration and try another run or two at the calibration...
View ArticleReply To: Thin Film Of Exposed Resin On Vat Bottom Making Long Print Times Fail
Panagiotis,Based on my observation, I think reflected white light is not that significant compare to ambient light in display frame area from the projector.As I mentioned in previous reply, I tried to...
View ArticleReply To: Thin Film Of Exposed Resin On Vat Bottom Making Long Print Times Fail
jkao,I didn’t check my laptop computer. But, the laptop (Samsung) has its own graphic control panel. I changed to have smaller gamma or brightness, that doesn’t change the projector ambient light...
View ArticleReply To: Thin Film Of Exposed Resin On Vat Bottom Making Long Print Times Fail
I started to look at the Brightness, Contrast, and Gamma settings but I don’t see enough of a noticeable change to feel this is going to have any real effect on solving the problem.Sure you can change...
View ArticleReply To: Thin Film Of Exposed Resin On Vat Bottom Making Long Print Times Fail
Panagiotis,I am testing with ND filter for 3DM-DENT resin. First print looks good. No thin layer found. But is was only 1 hour 30 min job.I am testing again which takes 4 hours. When I printed first...
View ArticleReply To: Thin Film Of Exposed Resin On Vat Bottom Making Long Print Times Fail
Yes to clarify, when I changed my B/W settings or gamma, I did this on the projector and the one menu item that seemed to have enough affect was the brightness control which I took down 2 or 1 notches....
View ArticleReply To: Thin Film Of Exposed Resin On Vat Bottom Making Long Print Times Fail
The only thing that previous users with the same issues reported working is changing laptops or changing output. One member was using a desktop machine with both a dedicated graphics card and an...
View ArticleReply To: Experiment with different resins
Thanks jkao! Can you open the attached settings files? I’ll include the file used for each of the two jobs (I renamed the Settings1.csv file to Differential_Job_1_ABS for clarity).One thing I noticed...
View ArticleReply To: Experiment with different resins
Tonight I tried printing with Form Labs Clear Resin. At 100 micron X, Y, Z resolution the exposure time is in minutes, not seconds. It is also very thick, somewhere between Makerjuice and corn syrup....
View ArticleReply To: Experiment with different resins
I’ll be interested to see whether those supports still come out with the Form1+ clear resin. The other clear resins I’ve tried all act as a light pipe for DLP and the supports expand into a solid layer...
View Article