Reply To: Layer cure time issue
Depending on the resin you are using and the XY resolution you are set to, that could be completely normal.What resolution are you printing at? What resin are you using?How do your settings compare to...
View ArticleIm contemplating getting a Titan 1 but…
Im very concerned about the user-friendliness of this 3d Printer. I am thinking about getting something more suited for a novice as myself.I need a SLA with a high resolution to create 32mm miniatures....
View ArticleReply To: Im contemplating getting a Titan 1 but…
Have you looked at my printing videos at:Especially the full print video?In general, you are not likely to find a printer that will just be push-button and go of any type, even if you go far far up the...
View ArticleReply To: Layer cure time issue
This may be a silly suggestion but make sure that you’ve removed the film from the bottom of the vat. I almost didn’t realize I was supposed to remove it for my first prints.
View ArticleReply To: Layer cure time issue
Umm… you can print on bare silicone, but only for the hard vat. You should not print bare on the soft vat.The vats are intended to print with the teflon film layer intact, and the printing surface will...
View ArticleReply To: Layer cure time issue
I meant the protective semi-opaque film that ships on the acrylic bottom with the vats for protection. I should have clarified: definitely do not remove the Teflon film -inside- the vat unless you’re...
View ArticleReply To: Weird sheet of cured resin with XGreen
I have done quite a few prints since changing the settings I described above, all of them under 2 hours but usually over 1 hour. Since changing the settings I have had zero background curing on the...
View ArticleReply To: Non-Settling Pigment – 1.5 micron molybdenum disulfide
@Jkao I was gonna give the Molybdenum Disulfide a try with MJG+. I’m curious, did you pour the Glycol Ether directly into the Moly bottle? And can you recommend an amount of Glycol to add? I’m...
View ArticleReply To: Non-Settling Pigment – 1.5 micron molybdenum disulfide
I don’t think you need the glycol ether necessarily. It just makes it a little easier to mix the moly evenly into the resin, since the glycol ether will wet the moly first, but from the pictures, the...
View ArticleClik here to view.
Reply To: Layer cure time issue
I’ve gone through many iterations of hard and soft vats and have not needed to remove any shipping acrylic from the inside.Oops, I wrote too soon, your confirming on the bottom ~ not the inside. Sorry....
View ArticleReply To: Ruby Package for sale (California)
On that note, I would be interested in buying an Colorado or close by Titan1. Anyone want to get rid of their’s, let me know.Jason
View ArticleReply To: Non-Settling Pigment – 1.5 micron molybdenum disulfide
One more thing to note is that the moly is not utterly non-settling. It will settle, somewhat noticeably after 4 days and quite dramatically after 14 days. I would probably only be comfortable with...
View ArticleReply To: Layer cure time issue
Sorry for the delay, I only work on this Thursdays and Fridays.Using 1920×1080, using Spot-A resin… rest of my setting from their test file work fine. Just didnt think that it would take this long per...
View ArticleReply To: Layer cure time issue
the Projector is always projecting at 1920×1080. As you move the projector up higher and closer to the vat, the actual projected light rectangle shrinks and this is what gives you 100µm (Projector...
View ArticleReply To: Layer cure time issue
Yes I did match the grid (as close as possible) If I move the projector up, what do I need to change besides the focus? Also, im guessing if I move it up I will just get a smaller print area?
View ArticleReply To: Layer cure time issue
That is correct. Looking at the Recommended Printing Parameters which I find to be pretty spot on...
View ArticleReply To: Layer cure time issue
Thank you for the link! not sure how I missed that… Makes it a lot easier to setup now.
View ArticleReply To: Layer cure time issue
Hope someone can answer another question for me… I just printed my first successful print, but I noticed it stuck to the bottom of the container and damaged it a little… What can I do to avoid that...
View ArticleReply To: Layer cure time issue
I remember how foreign this was when I started printing sla, in fact I just goofed a print I was doing for a customer in Spot-HT with settings that I’ve experimented with and it printed fine but was...
View Article